manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 93 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 93

Sensor

MAG 8000

(7ME6810)

MAG 8000

(7ME6880)

MAG 8000 CT

(7ME6820)

Max. excitation fre‐

quency

Advanced version

Battery-

powered

1/15 Hz for sensor size 

DN 25 ... 150 (1" ... 6") 

adjustable up to 6.25 Hz 

1/30 Hz for sensor size 

DN 200 … 600 (8" … 24") 

adjustable up to 3.125 Hz 

1/60 Hz for sensor size 

DN 700 ... 1200 (28" ... 48") 

adjustable up to 1.5625 Hz

 

1/15 Hz for sensor size 

DN 50 ... 150 (2" ... 6") 

adjustable up to 6.25 Hz

1/30 Hz for sensor size 

DN 200 … 600 (8" … 24") 

adjustable up to 3.125 Hz

Mains-

powered

6.25 Hz for sensor size 

DN 25 ... 150 (1" ... 6")

3.125 Hz for sensor size 

DN 200 … 600 (8" … 24")

1.5625 Hz for sensor size 

DN 700 ... 1200 (28" ... 48")

 

6.25 Hz for sensor size 

DN 25 ... 150 (1" ... 6")

3.125 Hz for sensor size 

DN 200 … 600 (8" … 24")

Liner

 

EPDM

Ebonite

EPDM

Electrode and 

grounding

 

Hastelloy C276

Stainless steel

Hastelloy C276

10.3

Transmitter

Transmitter

MAG 8000Standard

(7ME6810)

MAG 8000 Irrigation

(7ME6880)

MAG 8000 CT

(7ME6820)

Installation

 

Integral (compact) or remote with factory-mounted cable in 2*, 5, 10, 20 or 30 m lengths 

with IP68/NEMA 6P connectors.

Connection is made at the transmitter bottom.

Material

Top housing

Stainless steel (AISI 316)

Bottom

Coated brass

Wall mounting 

bracket

Stainless steel (AISI 304).

Display and 

key

Display

8 digits for main information.

Index, menu and status symbols for dedicated information

Key

For toggling through information and resetting of customer totalizer and call-up function

Menus

Selectable default information and accessible menus:

- Operator

- Meter

- Service

- Data Logger

- Statistic (Advanced version only)

- Revenue and Tariffs (Advanced version only)

Resolution

Totalized information can be displayed with 1, 2 or 3 decimals 

or automatic adjustment for maximum resolution

Technical data

10.3 Transmitter

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

93

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments