Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 27

Page: 27 / 164

Combination of metal and plastic pipes

Use straps for metal pipe and grounding rings for plastic pipe.

①

Metal pipe

②

Plastic pipe

Bonding/grounding straps, grounding rings and straps are not included in delivery.

Note
All straps or grounding wires must be 12 AWG (or heavier) copper wire and connected with 6

mm screws.

4.4

Cathodic-protected pipes

Pay special attention to meter installation in cathodic-protected pipe.

Isolate meter from pipeline by mounting isolation sleeves and washers on flange bolts and

connect a wire dimensioned to manage the cathodic current and environmental influence,

between pipelines.

Installing/Mounting

4.4 Cathodic-protected pipes

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews:

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 27 / 164

Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews: