manualshive.com logo in svg

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

The Siemens SIMOTION P320-4 E is a cutting-edge automation system with advanced features. Ensure a seamless setup and smooth operation by utilizing the comprehensive "Commissioning And Hardware Installation Manual". Download this valuable manual for free at our website, manualshive.com, to unlock the full potential of your Siemens SIMOTION P320-4 E.

Share
Download
background image

SRAM image (storage medium) or SRAM backup (storage medium) is OK, if:
● The SIMOTION software release of the SRAM image/backup matches the installed 

software release.

● Windows has been shut down properly (the POWER FAIL mechanism of SIMOTION P 

does not suffice here).

● The checksum test on the SRAM image/backup was successful.
● The battery status was good when the SRAM image was backed up.

Table 11-2

SRAM handling if the serial number is known  

SRAM

"OK"?

SRAM image

(storage medium)

"OK"?

SRAM backup

(storage medium)

"OK"?

User data

used

Note

Yes

Not applicable

Not applicable

Board 

1)

Normal statup

No

Yes

Not applicable

IMAGE 

2)

No message box or 

alarms

No

No

Yes

BACKUP 

3)

No message box or 

alarms

No

No

No

Overall reset

Required

1)

The user data backed up in the SRAM of the SIMOTION P320‑4 is used.

2)

The user data backed up in the SRAM image on the storage medium of the SIMOTION P320‑4 is 

used.

3)

The user data backed up in the SRAM backup on the storage medium of the SIMOTION P320‑4 is 

used.

If the serial number of the SIMOTION P320‑4 is not known:
The serial number of the SIMOTION P320‑4 does not correspond to the one that was last 

saved on the SIMOTION P320‑4, for example, after the replacement of the SIMOTION P320‑4.
SRAM image (storage medium) or SRAM backup (storage medium) is OK, if:
● The SIMOTION software release of the SRAM image/backup matches the installed 

software release.

● Windows has been shut down properly (the POWER FAIL mechanism of SIMOTION P 

does not suffice here).

● The checksum test on the SRAM image/backup was successful.
● The battery status was good when the SRAM image was backed up.

Table 11-3

SRAM handling if the serial number is unknown  

SRAM

"OK"?

SRAM image

(storage medium)

"OK"?

SRAM backup

(storage medium)

"OK"?

User data

used

Note

Yes

Yes

Not applicable

Board 

1)

 or IMAGE 

2)

Query made

Yes

No

Yes

Board 

1)

 or BACK‐

UP 

3)

Query made

Yes

No

No

Board 

1)

No message box 

No

Yes

Not applicable

IMAGE 

2)

No message box

Service and maintenance
11.5 Special power-up situations

SIMOTION P320-4 E / P320-4 S

190

Commissioning and Hardware Installation Manual, 11/2016

Summary of Contents for SIMOTION P320-4 E































































































































































































































Reviews:

No comments

Related manuals for SIMOTION P320-4 E

ABB RELION Series Product Manual preview
RELION Series
Brand: ABB Pages: 33
Parker F12-152 Series Service Manual preview
F12-152 Series
Brand: Parker Pages: 24
PWA Bernardo 1320 S Operator'S Manual preview
Bernardo 1320 S
Brand: PWA Pages: 12
Dr.X Works BHW-L Product Manual preview
BHW-L
Brand: Dr.X Works Pages: 14
Parker 8903/RS Technical Manual preview
8903/RS
Brand: Parker Pages: 40
K&S PU1 Instruction preview
PU1
Brand: K&S Pages: 6
Gardner Bender Ultra Brutus CP10K Instruction Sheet preview
Ultra Brutus CP10K
Brand: Gardner Bender Pages: 8
B DUTCH BD700.000043 Installation Manual preview
BD700.000043
Brand: B DUTCH Pages: 14
Raycus RFL-C8000S-CE User Manual preview
RFL-C8000S-CE
Brand: Raycus Pages: 54
PCB 1408-02ADB Installation And Operating Manual preview
1408-02ADB
Brand: PCB Pages: 16
Robland LBM Manual preview
LBM
Brand: Robland Pages: 72
Murata GQM22M5C2H680JB01 Series Reference Sheet preview
GQM22M5C2H680JB01 Series
Brand: Murata Pages: 25
Bosch 3 842 998 035 Assembly Instructions Manual preview
3 842 998 035
Brand: Bosch Pages: 64
Greenheck AMD-42-TD Installation, Operation And Maintenance Manual preview
AMD-42-TD
Brand: Greenheck Pages: 12
Greenheck Sure-Aire Installation, Operation And Maintenance Manual preview
Sure-Aire
Brand: Greenheck Pages: 16
Bungard RDC 30 Translation Of The Original Instructions preview
RDC 30
Brand: Bungard Pages: 13
THOMSON DFT-6300 User Manual preview
DFT-6300
Brand: THOMSON Pages: 38
360 Y-DROP Replacement Instructions preview
Y-DROP
Brand: 360 Pages: 2

Brands by name

Popular brands

Load more brands