Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download | Manualshive

Page: 127 / 222

background image

Parameter assignment/addressing

9

9.1

Parameter assignment / addressing requirements

The following actions should be completed before you start parameterizing or addressing:
● The SIMOTION P320‑4 and the other hardware are installed.
● The devices are connected.
● The required software is installed.
● The SIMOTION P320‑4 has been switched on.
The actual state should be saved after the parameterization.

9.2

Factory settings

9.2.1

Factory settings overview

Requirement

You have obtained information about the various communications models. Further information

can be found under HMI and SIMOTION SCOUT (Page 59).
You are familiar with the Windows Control Panel.

Resetting the factory settings

It is possible to reset SIMOTION P320‑4 to the factory settings (see section Resetting the

SIMOTION P to the initial state (Page 183)).

9.2.2

Ethernet - TCP/IP local

SIMOTION P320‑4 delivery state
Local communication in the SIMOTION P320‑4 between Windows programs such as HMI and

the SIMOTION P Runtime software is handled via the preset TCP/IP Ethernet communication.
As an alternative to TCP/IP, the PC internal (local) communication can also be used. Further

information on how to check the settings in the Windows Control Panel can be found in Section

Check PC internal settings (Page 137).

SIMOTION P320-4 E / P320-4 S

Commissioning and Hardware Installation Manual, 11/2016

127

«
...
125
126
127
128
129
...
»

Summary of Contents for SIMOTION P320-4 E































































































































































































































Reviews:

No comments

Related manuals for SIMOTION P320-4 E

Brand: TDW Pages: 2

Brand: Vahle Pages: 36

Brand: Vahle Pages: 20

Brand: Vacon Pages: 102

Brand: Ideal Heating Pages: 16

Brand: C.B.S. SCIENTIFIC Pages: 16

Brand: REMS Pages: 96

Brand: Watts Pages: 72

NZM3-4-XKVI2P Series

Brand: Eaton Pages: 3

ZeroVise M Series

Brand: ZeroClamp Pages: 44

Brand: Pronomic Pages: 16

Brand: Ampeon Pages: 35

Brand: Systec & Solutions Pages: 41

Brand: ebm-papst Pages: 14

Brand: R.V.R. Elettronica Pages: 38

S-CON MINI CURVE SDBR

Brand: SANKI Pages: 16

NHI-E PKZ0 Series

Brand: Moeller Pages: 2

Brand: Moeller Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands