Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download | Manualshive

Page: 86 / 222

background image

To insert the CFast card into the memory card slot again:
Push the CFast card into the memory card slot until it locks into place (ball-point pen

mechanism).

5.5.1

Automatic restart for SIMOTION P Runtime

Note
Not a Windows restart
Note that this is not a Windows restart!

Starting the SIMOTION P320-4 with withdrawn CFast card
Power-up of the SIMOTION P Runtime is not possible without the CFast card. A prompt

referring to the missing CFast card is displayed. The prompt is displayed until the CFast card

is inserted. The power-up is then continued and the prompt closed automatically.
The automatic restart of the SIMOTION P Runtime is performed when the Enabled checkbox

is activated in the SIMOTION P Control Manager in the Administration tab at Automatic Restart

By Plug-In External Memory Card.

Figure 5-4

Prompt about the missing CFast card - automatic restart Enabled

Note
The prompt does not close automatically after inserting the CFast card.
If the prompt shown above is not automatically closed after inserting the CFast card and there

is no automatic restart of the SIMOTION P Runtime, check the BIOS settings.
See Section Hotplug Enabled BIOS settings (Page 203).

If the Disabled status has been selected in the SIMOTION P Control Manager, there is no

automatic restart of the SIMOTION P Runtime after the CFast card has been inserted. In this

case, the following prompt is displayed.

Mounting
5.5 Withdrawing/inserting the CFast card

SIMOTION P320-4 E / P320-4 S

86

Commissioning and Hardware Installation Manual, 11/2016

«
...
84
85
86
87
88
...
»

Summary of Contents for SIMOTION P320-4 E































































































































































































































Reviews:

No comments

Related manuals for SIMOTION P320-4 E

Brand: vc999 Pages: 59

Brand: V.ORLANDI Pages: 144

Brand: Swienty Pages: 31

Brand: Huayu Pages: 12

Brand: SAMCHULLY Pages: 44

Brand: Grizzly Pages: 44

MICROPLUS MP 075 C

Brand: ANTEO Pages: 108

Brand: hager Pages: 2

Brand: Alpha Technologies Pages: 64

Siemens APOGEE P1

Brand: Parker Pages: 20

Brand: TQC Pages: 23

Sibo SZB SE 33U

Brand: Elektro-Automatik Pages: 16

Vickers TZ Series

Brand: Eaton Pages: 22

Brand: York Pages: 24

Brand: King Young Pages: 2

Brand: Advantech-DLoG Pages: 2

ICE MASTER IMT1000

Brand: CAMION Pages: 72

Brand: Xciel Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands