Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download

Page: 185 / 222

11.4

Installing/removing the back-up battery of the SIMOTION P320-4

11.4.1

Preventive maintenance

To maintain high system availability, we recommend the preventative exchange of those PC

components that are subject to wear. The table below indicates the intervals for this exchange.

Component

Exchange interval:

CMOS backup battery

4 years

11.4.2

Replacing the backup battery

Note
The service life of the backup battery is approximately 5 - 8 years, depending on the

environmental conditions.

To be noted before you replace the battery

NOTICE
Risk of damage!
The lithium battery may only be replaced with an identical battery or with a type recommended

by the manufacturer (article number: A5E30314053)

WARNING

Risk of explosion and release of harmful substances!
Therefore, do not throw lithium batteries into an open fire, do not solder or open the cell body,

do not short-circuit or reverse the polarity, do not heat to above 100° C, dispose of them in

accordance with regulations, and protect them from direct exposure to sunlight, humidity, and

condensation.

Note
A backup battery maintains the contents of the SRAM data on the SIMOTION P320‑4 after

the supply power is switched off.

Service and maintenance

11.4 Installing/removing the back-up battery of the SIMOTION P320-4

SIMOTION P320-4 E / P320-4 S

Commissioning and Hardware Installation Manual, 11/2016

185

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands