Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download

Page: 202 / 222

FAQs / error correction

Possible cause

Possible remedy

Error message on the

screen:
Operating system not found

● No operating system

present.

● Incorrect active boot

partition.

● Incorrect drive entries in

the SETUP.

Check whether one of the specified causes is present:

Wrong time and/or date on

the PC.

● Press <ESC> during the boot sequence to open BIOS Setup.

Detailed information on the BIOS setup can be found in the
section Starting Bios settings Hotplug Enabled - BIOS
Setup (Page 203).

● Set the time and date in the setup menu.

Although the BIOS setting is

OK, the time and date are

still wrong.

The backup battery is emp‐

ty.

Replace the backup battery.
See Section Service and maintenances > Replacing the back-

up battery (Page 185).
If the problem cannot be resolved by replacing the battery, then

contact your technical support team.

UPS does not function.

The operating system does

not have a suitable driver for

the UPS.

Install a suitable driver; the correct driver can often be downloa‐

ded from the homepage of the device's manufacturer.
See also Section Customer-specific software (Page 118).

IP address assigned twice

(e.g. through series commis‐

sioning).

Default IP address for Win‐

dows
See Default IP addresses

for Windows and SIMO‐

TION P (Page 143).

Assign a new IP address for Windows.
The IP address must be different to the previous specified IP

address and must not have been assigned already in the net‐

work.

The display in the BIOS for

the PROFINET MAC ad‐

dress is incorrect

(00:00:00:00:00:00).

The correct MAC addresses can be taken from the rating plate

on the housing.
See also Manual SIMOTION P320-4 E / P320-4 S Manual, Sec‐

tion Device identification data, MAC addresses.

Troubleshooting/FAQs
13.1 Error correction

SIMOTION P320-4 E / P320-4 S

202

Commissioning and Hardware Installation Manual, 11/2016

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands