Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download

Page: 143 / 222

9.5.3

Default IP addresses for Windows and SIMOTION P Runtime

Default Ethernet addresses for use from Windows and SIMOTION P are preset.

Table 9-2

Default Ethernet address for Windows and SIMOTION P Runtime

Ethernet interface

Windows

SIMOTION P Runtime

Onboard Ethernet 1

169.254.11.21

169.254.11.22

The default IP address for Windows can result in IP addresses being assigned twice, e.g.

during series commissioning (see Troubleshooting/FAQs (Page 201)).
If DHCP is set under Windows, the IP addresses for Windows are determined automatically.

9.5.4

Communication via an Ethernet interface

If both Windows and SIMOTION use the onboard Ethernet interface X1, the following

configuration is present:

6XEQHWV

URXWHUSRVVLEOH

6,027,21b3

2QERDUG(WKHUQHW;

6,027,2135XQWLPH

,3DGGUHVV

:LQGRZV

'HIDXOW

*DWHZD\

6,027,21

Figure 9-13 Distribution of the IP addresses for Windows and SIMOTION P Runtime

Note
If no change of the default IP addresses is desired, all conditions with the default IP addresses

are fulfilled and no change is required.

Parameter assignment/addressing

9.5 Ethernet communication

SIMOTION P320-4 E / P320-4 S

Commissioning and Hardware Installation Manual, 11/2016

143

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands