Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download

Page: 201 / 222

Troubleshooting/FAQs

13.1

Error correction

This section provides you with tips on how to locate and troubleshoot common problems.

FAQs / error correction

Possible cause

Possible remedy

The device is not operation‐

al.

There is no power supply to

the device.

● Check whether the 24 VDC power supply is connected.

See SIMOTION P320-4 E / P320-4 S Manual, Section
Connecting the power supply (24 VDC).

● Check whether the line side switch is activated.

See SIMOTION P320-4 E / P320-4 S Manual, Section
Operator controls.

SIMOTION P does not start

after connecting the CFast

card.

BIOS settings are not set to

Hotplug Enabled.

You can find out how to check and correct the BIOS settings in

Section Hotplug Enabled BIOS settings (Page 203).

SIMOTION P does not start

after a reboot.

The user is not logged in au‐

tomatically.

Set the password for the AutoLogin (Automatically Log On).
See Section SIMOTION P AutoLogin (Page 91).

The monitor remains dark.

The monitor is switched off. Switch on the monitor.
The monitor is in "power‐

save" mode.

Press any key on the connected keyboard.

The brightness button has

been set to dark.

Set the monitor brightness button to obtain more light.
For detailed information, refer to the monitor operating instruc‐

tions.

The power cord or the mon‐

itor cable is not connected.

● Check whether the power cord has been properly connected

to the monitor and to the system unit or to the grounded
shockproof outlet.

● Check whether the monitor cable has been properly

connected to the system unit and to the monitor.

If the monitor screen still remains dark after you have performed

these checks, please contact your technical support team.

The mouse pointer does not

appear on the screen.

The mouse driver is not loa‐

ded.

Check whether the mouse driver is properly installed and

present when you start the application program.
For more detailed information on the mouse driver, refer to the

documentation for the mouse or application programs.

The mouse is not connec‐

ted.

Check whether the mouse is properly connected to the system

unit. If you use an adapter or extension on the mouse cable,

also check the connectors.
If the cursor still does not appear on the screen after you have

performed these checks and measures, please contact your

technical support team.

SIMOTION P320-4 E / P320-4 S

Commissioning and Hardware Installation Manual, 11/2016

201

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands