manualshive.com logo in svg

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

The Siemens SIMOTION P320-4 E is a cutting-edge automation system with advanced features. Ensure a seamless setup and smooth operation by utilizing the comprehensive "Commissioning And Hardware Installation Manual". Download this valuable manual for free at our website, manualshive.com, to unlock the full potential of your Siemens SIMOTION P320-4 E.

Share
Download
background image

&XUUHQWGDWD

.HUQHOGDWD

5HWDLQGDWD

2SHUDWLQJV\VWHP

6,027,21b3

)LUPZDUH

6,027,21b3

6WRUDJHPHGLD

6WRUDJHPHGLXP

LQWHUQDO

66'

&)DVWFDUG

&)DVWFDUG

6WRUDJHPHGLXP

H[WHUQDO

%DFNXSV

8VHUGDWD

6,027,213

65$0

5$0

Figure 10-8 SRAM restore at startup

Further information
can be found in the section Non-volatile data and SRAM handling (Page 189).

10.8.4.3

Backing up non-volatile SIMOTION data (retain data)

The non-volatile SIMOTION data (retain data) can be backed up from the user program and 

via SIMOTION SCOUT. 
You can use the backup to restore the retain data independent of the version after an update 

or a hardware replacement (SIMOTION P320‑4) or to create a current backup to use in the 

event of an inadvertent deletion.
You can save the retain data as follows:
● From the user program with the  _savePersistentMemoryData() system function

The contents are saved to the "PMEMORY.XML" backup file in the "USER\SIMOTION" 

directory.

The data is saved in the PMEMORY.XML file on the external CFast card.

● To back up the retain data via SIMOTION SCOUT , go online and in the context menu of 

a created source, execute Save variables.... 

The data is saved in the unitdata.xml file on the computer with SIMOTION SCOUT .

● Alternatively, the retain data is saved via the SIMOTION P State application, via the 

SIMOTION P > Set Diagnostic Switch menu.

The contents are saved to the "PMEMORY.XML" backup file in the "USER\SIMOTION\HMI

\SYSLOG\DIAG" directory.

● To restore the retain data via SIMOTION SCOUT, go online and execute Restore 

variables... in the menu.

Restores the saved variables, also over different versions.

On the system side, the _savePersistentMemoryData() system function ensures that a 

consistent overall image of the non-volatile SIMOTION data is always available the next time 

the device is switched on, even if there is a power failure during backup. 
An already existing backup file is renamed to "PMEMORY.BAK" before a new backup file is 

generated. If the save operation to the new backup file fails (e.g. because the capacity of the 

external CFast card is insufficient), this backup copy of the backup file is used the next time 

Commissioning (software)
10.8 Data storage concept

SIMOTION P320-4 E / P320-4 S

166

Commissioning and Hardware Installation Manual, 11/2016

Summary of Contents for SIMOTION P320-4 E































































































































































































































Reviews:

No comments

Related manuals for SIMOTION P320-4 E

ABB ACS880-01 Series Installation Manual preview
ACS880-01 Series
Brand: ABB Pages: 238
Vahle U35 Installation Instructions Manual preview
U35
Brand: Vahle Pages: 28
493K K-Paq Junior Owner'S Manual preview
K-Paq Junior
Brand: 493K Pages: 65
Jäger 10406064 Manual preview
10406064
Brand: Jäger Pages: 48
IGM 141-DC30 Operating Instructions Manual preview
141-DC30
Brand: IGM Pages: 8
Veeco K465i GaN Operation And Maintenance preview
K465i GaN
Brand: Veeco Pages: 352
MIR 250 Shelf Carrier User Manual preview
250 Shelf Carrier
Brand: MIR Pages: 249
Genmitsu Jinsoku LE-1620 User Manual preview
Jinsoku LE-1620
Brand: Genmitsu Pages: 29
GEOFABRICS ELCOROCK FILLING FRAME Operating And Safety Instructions Manual preview
ELCOROCK FILLING FRAME
Brand: GEOFABRICS Pages: 7
Delta HEX070PB Specification And Manual preview
HEX070PB
Brand: Delta Pages: 15
STABILUS FYT-LA3 Operating And Mounting Instructions preview
FYT-LA3
Brand: STABILUS Pages: 4
Advantech PCIE-1840 User Manual preview
PCIE-1840
Brand: Advantech Pages: 38
Kontron Embedded Computers V Box Express II User Manual preview
V Box Express II
Brand: Kontron Embedded Computers Pages: 46
Global WF 1767-70 Series Instruction & Parts Manual preview
WF 1767-70 Series
Brand: Global Pages: 64
Datacolor AHIBA IR Installation Manual preview
AHIBA IR
Brand: Datacolor Pages: 3
OEZ BZ-BX-X230-A Instructions For Use Manual preview
BZ-BX-X230-A
Brand: OEZ Pages: 6
Gardner Bender BE400 Eegor Instruction Sheet preview
BE400 Eegor
Brand: Gardner Bender Pages: 4
CAB 4114 Series Service Manual preview
4114 Series
Brand: CAB Pages: 44

Brands by name

Popular brands

Load more brands