Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download | Manualshive

Page: 87 / 222

background image

Figure 5-5

Prompt about the missing CFast card - automatic restart Disabled

CFast card withdrawn during operation
If the CFast card is withdrawn during normal operation, the SIMOTION P Runtime goes into

the General reset request state.
This state can be exited through MRES (general reset) on the mode selector or a restart via

SIMOTION P State.
In addition to the general reset request, a prompt is also displayed informing about the

withdrawn CFast card and whether an automatic restart of the SIMOTION P Runtime will be

performed.

Note
Automatic restart for SIMOTION P Runtime setting
The automatic restart settings are made in the SIMOTION P Control Manager.
The default setting in the Administration tab at Start SIMOTION P is Enabled.
Further information can be found in Section SIMOTION P Control Manager > Administration

tab > Automatic Restart By Plug-In External Memory Card (Page 132).

5.6

Installing the SIMOTION P320-4 in the control cabinet

5.6.1

Notes on installation

Requirement

Before you install the device, observe the following installation notes:

NOTICE
Observe the DIN/VDE requirements
Adhere to the relevant DIN/VDE requirements or the country-specific regulations when

installing in cabinets.

Mounting

5.6 Installing the SIMOTION P320-4 in the control cabinet

SIMOTION P320-4 E / P320-4 S

Commissioning and Hardware Installation Manual, 11/2016

87

«
...
85
86
87
88
89
...
»

Summary of Contents for SIMOTION P320-4 E































































































































































































































Reviews:

No comments

Related manuals for SIMOTION P320-4 E

Bernardo 1320 S

Brand: PWA Pages: 12

Brand: Conductix-Wampfler Pages: 12

Flumen OPTI-TR 22

Brand: Wilo Pages: 88

Brand: PPI Pages: 32

Eastey Value Series

Brand: Rapid Packaging Pages: 49

Brand: Anywire Pages: 6

Brand: ABB Pages: 108

Brand: ABB Pages: 108

AES-1210 Series

Brand: Advanipc Pages: 52

ROTA-S plus 2.0

Brand: SCHUNK Pages: 40

ROTA TB2 1000-560

Brand: SCHUNK Pages: 69

Brand: A.u.S Pages: 60

Brand: Tronair Pages: 8

Brand: REMS Pages: 7

Brand: REMS Pages: 201

Brand: Marley Pages: 24

Brand: Doosan Pages: 122

Brand: Datalogic Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands