Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download

Page: 120 / 222

Figure 8-2

SIMOTION P State - PROFINET onboard and additionally with optional IsoPROFIBUS
board

Note
The SIMOTION P State application is in English.
Generally, only English is supported on the SIMOTION P320-4, this also applies for the Win7

operating system.

8.1.2

LED display

Meaning of LEDs

The meaning of the LEDs and their colors is described in the table below.

LED display

Meaning

Description

Red

Fault

The fault state of the SIMOTION P320-4 is displayed.

RUN

Green

SIMOTION P320-4 in RUN

mode

The user program is running.

STOPU Yellow

SIMOTION P320-4 in the

STOP User Program

The technology packages (e.g. synchronous operation, cam) are ac‐

tive. Test and commissioning functions can be executed without a

user program.

The user program is not active.

STOP

Yellow

SIMOTION P320-4 in STOP

mode

There is no user program running.

The technology packages are not active.

SF PN

Red

PROFINET bus fault

A fault state is displayed on the PROFINET interface (X3).

SY/MT

Yellow

Sync of the PROFINET inter‐

face

It is displayed whether the PROFINET interface has been synchron‐

ized.

BUS1F

Red

Group fault

A fault state is displayed on the IsoPROFIBUS interface (X101).

BUS2F

Red

Group fault

A fault state is displayed on the IsoPROFIBUS interface (X102).

Operator Control (hardware)
8.1 SIMOTION P state application

SIMOTION P320-4 E / P320-4 S

120

Commissioning and Hardware Installation Manual, 11/2016

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands