Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download Page 105

Page: 105 / 222

6.5.2

SYNC I/O connecting cable / Plugging in the IsoPROFIBUS board

To be able to plug in the IsoPROFIBUS board, the device must be opened and the SYNC I/O

connecting cable must be rerouted:
1. Remove the screws of the upper cover plate and open the SIMOTION P320-4.

At the factory, the SYNC I/O connecting cable is secured in the device using an adhesive

tape.

Figure 6-4

Opened SIMOTION P320-4 with SYNC I/O connecting cable as delivered ex works

2. Remove the adhesive tape and change the position of the SYNC I/O connecting cable as

follows:

the SYNC I/O connecting cable is routed to the interface side of the device and secured

there again.

Connection

6.5 Connecting PROFIBUS

SIMOTION P320-4 E / P320-4 S

Commissioning and Hardware Installation Manual, 11/2016

105

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands