manualshive.com logo in svg

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

The Siemens SIMOTION P320-4 E is a cutting-edge automation system with advanced features. Ensure a seamless setup and smooth operation by utilizing the comprehensive "Commissioning And Hardware Installation Manual". Download this valuable manual for free at our website, manualshive.com, to unlock the full potential of your Siemens SIMOTION P320-4 E.

Share
Download
background image

Battery monitoring

The 3 V lithium battery to back up the SRAM and the clock module is monitored in two stages:

Table 11-1

Two-stage battery monitoring

Battery voltage

Message

2.7 V ± 0.1 V

Diagnostic buffer entry: Battery warning
Battery warning threshold reached

2.25 V ± 0.25 V

Diagnostic buffer entry: Battery error
Voltage below limit

In order to prevent data being lost, the battery should be replaced once the Battery warning 

entry appears in the diagnostics buffer or, at the very latest, the first time the Battery error entry 

appears in the diagnostics buffer.

Disposal

NOTICE
Dispose of batteries properly
Batteries must be disposed of in accordance with local regulations.

Preparation

Note
The configuration data and contents of the SRAM in the device are buffered for at least 30 

seconds when the battery is replaced.   

Preparation – make a note of the BIOS settings

Note
Note specific BIOS setup settings if changes have been made.

Service and maintenance
11.4 Installing/removing the back-up battery of the SIMOTION P320-4

SIMOTION P320-4 E / P320-4 S

186

Commissioning and Hardware Installation Manual, 11/2016

Summary of Contents for SIMOTION P320-4 E































































































































































































































Reviews:

No comments

Related manuals for SIMOTION P320-4 E

Idex Hale Sam Operation Installation Maintenance Manual preview
Hale Sam
Brand: Idex Pages: 141
SCHUNK PFH 30 Assembly And Operating Manual preview
PFH 30
Brand: SCHUNK Pages: 35
Carbatec TH-B317P Owner'S Manual preview
TH-B317P
Brand: Carbatec Pages: 29
Moxa Technologies UC-8112-LX STK Hardware Quick Installation Manual preview
UC-8112-LX STK
Brand: Moxa Technologies Pages: 2
Rohm BU2365FV Technical Notes preview
BU2365FV
Brand: Rohm Pages: 17
Sima STAR 16 Original User Manual preview
STAR 16
Brand: Sima Pages: 22
P.A. SRF-48 Installation Manual preview
SRF-48
Brand: P.A. Pages: 17
VELCORP GEMS VELS LC-1EY-HGS-R Assembly Instruction preview
LC-1EY-HGS-R
Brand: VELCORP GEMS VELS Pages: 2
Mayr ROBA-brake-checker plus DC 028.600.2 Installation And Operational Instructions preview
ROBA-brake-checker plus DC 028.600.2
Brand: Mayr Pages: 10
VALSTEAM ADCA FLT17 Installation And Maintenance Instructions preview
FLT17
Brand: VALSTEAM ADCA Pages: 5
Nordson MELTEX PG Series Manual preview
MELTEX PG Series
Brand: Nordson Pages: 16
SAINT-GOBAIN CertainTeed Volu-Matic 200 Operation Manual And Safety Information preview
CertainTeed Volu-Matic 200
Brand: SAINT-GOBAIN Pages: 52
SIGMATEK C-IPC 171 Manual preview
C-IPC 171
Brand: SIGMATEK Pages: 42
SCMI K8 Manual preview
K8
Brand: SCMI Pages: 17
Wyko NT3300 Operating Instructions Manual preview
NT3300
Brand: Wyko Pages: 9
Kval 700-DC Operation And Service Manual preview
700-DC
Brand: Kval Pages: 72
TLS DCV-600 Manual preview
DCV-600
Brand: TLS Pages: 8
HIOS HSV-10RB Instruction Manual preview
HSV-10RB
Brand: HIOS Pages: 36

Brands by name

Popular brands

Load more brands