Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download

Page: 147 / 222

NOTICE
SIMOTION P Runtime
During the runtime of SIMOTION P, the Windows settings must be activated for the onboard

Ethernet interface.
The onboard Ethernet interface must not be deactivated or activated during operation.

9.5.5

Establishing the active flag for an external PG/PC

Requirement

A PG/PC is required to create projects and download them to the target device.

SIMOTION SCOUT can only be installed on the SIMOTION P320‑4 S.

Note
Observe the online access point for SIMOTION P320-4 S
For SIMOTION P320-4 S, use S7ONLINE as access point to avoid inconsistencies.

Procedure

Proceed as follows to open NetPro and assign an interface in the PG/PC:
1. Open the project in SIMOTION SCOUT.
2. Click the button Open NetPro.

NETPRO is accessed, and the configured network is graphically displayed. The PG/PC

connection to the configured network is shown not bold and in a color other than yellow.

3. Double-click on the PG/PC that you would like to configure.

The Properties - PG/PC dialog box is displayed with the Assignment tab in the foreground.

4. In the field Assigned: select the interface and activate S7ONLINE access by clicking the

corresponding checkbox.

5. Accept the settings by clicking OK.

The PG/PC connection to the configured network is now displayed in bold and yellow.

6. Save the changes via Network > Save and compile and upload them to SIMOTION P320-4.

Result

Now you can go online via the PG/PC.

Parameter assignment/addressing

9.5 Ethernet communication

SIMOTION P320-4 E / P320-4 S

Commissioning and Hardware Installation Manual, 11/2016

147

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands