Siemens SIMOCODE 3UF Programming And Operating Manual Download Page 85

Page: 85 / 172

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

Standard Functions

12.1

Test - Reset

12.1.1

Test - Reset

The function of the "TEST/RESET" button on the Basic Unit is generally dependent upon the

operating status of the device:

●

Reset function: if a fault occurs

●

Test function: in other operating states.

In addition to the TEST/RESET buttons, SIMOCODE pro allows internal Test/Reset tripping

via the Test function block. The Test function block consists of 1 plug.
Overall, there are 2 Test 1 and Test 2 function blocks for BU1 and BU2, whereby each

function block has a slightly different function:

●

Test 1: When testing/tripping the output relays

●

Test 2: Without tripping the output relays (normally for testing via the bus).

12.1.2

Test

Carrying out testing
Testing can be carried out as following:

●

Via the "TEST/RESET" button on the Basic Unit and on the Operator Panel (can be

deactivated) as well as via PC with the Device Integration Manager.

●

Via the plugs of the internal Test 1 or Test 2 function blocks.

●

Via the menu of the Operator Panel with Display (e.g. the "commands" menu item).

Testing can be terminated at any time - it does not influence the thermal motor

model/overload function, i.e. after switching off via TEST, the system can be reset

immediately. Tripping only occurs for Test 1 when the operating mode is set to "Remote".

Summary of Contents for SIMOCODE 3UF













































































































































































Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands

Siemens SIMOCODE 3UF, Programming And Operating Manual

Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands