Siemens SIMOCODE 3UF Programming And Operating Manual Download Page 164

Page: 164 / 172

Online Settings and Displays

17.12 Status Information

SIMOCODE PRO V PN FDI

164

Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

17.12

Status Information

Different events are indicated in the plain language in the "Events" register of the Target

system > Faults/Warnings/Status information mask:

Indication

Meaning/Possible cause/Acknowledgement/Error processing

Parameter blocking during startup

active

The start-up parameter block prevents SIMOCODE pro

parameters which could be saved in the controller from being

accepted.
The block must be set when SIMOCODE ES or Device

Integration Manager is used for parameterizing.
The block may not be set when SIMOCODE pro is integrated in

STEP 7 via the SIMOCODE pro Object Manager (OM) or

SIMOCODE pro C was parameterized via GSD.

Configuration fault

The configured device configuration does not match the current

configuration.

•

Please check if all configured components are present.

•

Check the actual configuration using "Configuration".

Rectify the fault; Reset.

Required function is not supported At least one parameterized function is not supported by the

product version of the Basic Unit.

•

Only activate functions that are supported by the product

version of the Basic Unit. For example, SIMOCODE pro V

Basic Units with the product version E01 do not support the

voltage measuring module, the temperature module and the

analog module.

Parameter is faulty

There is a fault in the parameter data transmitted to the device.
Faults can occur in the parameter data, for example, if the

device parameterization was not carried out with SIMOCODE

ES or Device Integration Manager.

•

Check the parameter data (data records 130 - 133)

transmitted to the device to make sure that the contents are

correct.

Changing of the parameters is not

permissible in the current mode

Changing of a least one parameter is not possible in the current

operating state. A lot of parameters can only be changed when

the motor feeder is switched off and is not in the "Remote"

operating mode.

Wrong password

The SIMOCODE pro parameters are protected by a password.

An attempt was made to change the parameters without

entering the password.

•

If you do not know the password, new parameters cannot be

set until the factory default settings have been reset.

Summary of Contents for SIMOCODE 3UF













































































































































































Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands

Siemens SIMOCODE 3UF, Programming And Operating Manual

Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands