Siemens SIMOCODE 3UF Programming And Operating Manual Download Page 87

Page: 87 / 172

Standard Functions

12.1 Test - Reset

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

12.1.3

Reset

Carrying out Reset
Resetting can be carried out as follows:

●

Via the "TEST/RESET" button on the Basic Unit and on the Operator Panel (can be

deactivated) as well as via PC with the Device Integration Manager.

●

Via the "Reset Input" plug of the internal function blocks via the plugs of the internal

function blocks Reset 1, Reset 2 and Reset 3.

●

Via the menu of the Operator Panel with Display (e.g. the "commands" menu item).

Reset 1-3 - Input

Control of the Reset function block from any signal (any sockets, e.g. device inputs, control

bits from PROFINET, etc.)

Reset 1-3 - TEST/RESET button blocked

The blue TEST/RESET buttons on the Basic Unit and on the Operator Panel are intended for

acknowledging faults and carrying out device tests.

The buttons can be locked via "TEST/RESET buttons blocked". These can then be used for

other purposes. On the Operator Panel with Display, blocking is carried out via the menu

(default: unblocked).

Acknowledgement of faults

Generally, the following applies to the acknowledgement of faults:

●

Faults can be acknowledged:
–

If the cause of the fault has been eliminated.

–

If there is no "ON" control command pending.

●

A reset will not be possible if the cause of the fault has not been eliminated or if an "ON"

control command is pending. The reset will be saved depending on the type of fault.

Saving a reset is indicated by the "GEN. FAULT" LED on the Basic Unit and on the

Operator Panel. The LEDs change from flashing to continuous signal.

Automatic acknowledgement of faults

Faults are automatically acknowledged in the following cases:

●

A reset has been saved and the cause of the fault is no longer present (user has

previously acknowledged the fault).

●

Auto-reset of overload tripping or thermistor tripping if motor protection reset = Auto

(acknowledgement is automatic following expiration of the cooling down period). The

motor cannot start immediately since resetting is not possible if an ON command is

pending.

Summary of Contents for SIMOCODE 3UF













































































































































































Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands

Siemens SIMOCODE 3UF, Programming And Operating Manual

Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands