Siemens SIMOCODE 3UF Programming And Operating Manual Download Page 34

Page: 34 / 172

Motor Control

8.2 Control Station

SIMOCODE PRO V PN FDI

Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

8.2.5

PC - OPC-UA [HMI]

This control station is primarily intended for switching commands on an arbitrary PC that,

along with the automation system, is used as a second master on PROFINET or that, as a

client, accesses the data made available by SIMOCODE pro, as server, via OPC-UA. The

control commands are transferred using a client-server connection via OPC-UA.

Note
If the SIMOCODE ES Professional or Device Integration Manager is connected to

SIMOCODE pro via PROFINET, its control commands automatically take effect via the

"PC/OPC-UA" control station.
At the same time, the enabled commands for this control station also take effect for

SIMOCODE ES.

8.2.6

Operator Panel [OP]

This control station is primarily intended for control commands issued via the buttons of the

3UF72 Operator Panel which is e.g. mounted in a switchgear cabinet door. The plugs of the

Control Stations function block must be connected to arbitrary sockets (normally with the

function block for the buttons of the Operator Panel - OP Buttons) for the control commands

to take effect.

Note
Since the operator panel only has four buttons for controlling the motor feeder, one button

must be used as a speed switch button for control functions with two rotational speeds and

two directions for rotation.

For this purpose, the button must be assigned to the internal control command "[OP] <>/

<<>>".

Summary of Contents for SIMOCODE 3UF













































































































































































Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands

Siemens SIMOCODE 3UF, Programming And Operating Manual

Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands