Siemens SIMOCODE 3UF Programming And Operating Manual Download Page 93

Page: 93 / 172

Standard Functions

12.4 Operational Protection OFF (OPO)

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

12.3.2.3

External Fault 1-6 Reset

Specification of further (common) acknowledgement options using additional reset types:

●

TEST/RESET buttons on the Basic Unit and the Operator Panel (panel reset)

●

Remote reset: Acknowledgement via Reset 1-3, control bit "Reset" command

●

Auto reset: The trip resets itself after the cause has been eliminated (after removal of the

activation signal)

●

OFF command reset: "OFF" control command resets the fault.

12.4

Operational Protection OFF (OPO)

The Operational Protection Off (OPO) function block returns the Positioner to a safe position.

In order to do this, the input (plug) must be connected to the respective socket (e.g. device

inputs, control bits from PROFINET, etc.).
The Operational Protection Off function block consists of:

●

1 plug

●

1 "Status - OPO" socket. This is set when a signal is pending at the Input.

●

1 "Trip - OPO Fault" socket. This is set when the respective, safe end position has been

reached.

Overall, there is 1 "Operational Protection Off (OPO)" function block for BU2.

Settings Operational Protection OFF (OPO)

Input

Control of the Operational Protection function block using the

monitored signal (any sockets, e.g. device inputs, etc.)

Positioner response

Specification of the response for the Positioner control function and

accordingly Solenoid Valve control function when activated via the

Input:

•

CLOSED: Positioner moves to the "Closed" end position

•

OPEN: Positioner runs in the "Open" end position

Type

Specification of the input logic:

•

NO contact (1-active)

•

NC contact (0-active).

Summary of Contents for SIMOCODE 3UF













































































































































































Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands

Siemens SIMOCODE 3UF, Programming And Operating Manual

Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands