Siemens SIMOCODE 3UF Programming And Operating Manual Download Page 40

Page: 40 / 172

Motor Control

8.3 Control Function

SIMOCODE PRO V PN FDI

Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

8.3.4

Timings

Parameter

Description

Feedback time (CiR)

SIMOCODE pro monitors the status of the feeder (ON or

OFF) via FB ON If the status of FB ON changes - without a

corresponding switching command - the trip feedback (FB)

switches off the feeder. Default: 0.5 s.The feedback time

can be used to suppress such "feedback faults" for a

defined period of time, e.g. in the case of network switches.

SIMOCODE pro continuously controls if FB ON = 0. If the

current flows longer than the set feedback time without the

"ON" control command being issued, fault message "Trip -

Feedback (FB) ON" is issued. The contactor controls can

only be connected after the fault has been rectified. When

the motor is switched on, SIMOCODE pro continuously

controls if FB ON = 1. If the current flows longer than the set

feedback time without the "OFF" control command being

issued, a fault message "trip - feedback (FB) OFF" is

issued. The contactor controls are deactivated.

Execution time (CiR)

SIMOCODE pro monitors switching on/switching off.

Switching on/switching off must be completed within this

time period. Default: 1.0 s. After the "ON" control command

is issued, SIMOCODE pro must be able to detect current in

the main circuit within the execution time. Otherwise, the

fault message "trip - execution ON command" will be

issued. SIMOCODE pro deactivates the contactor controls.

After the "OFF" control command is issued, SIMOCODE pro

must not be able to detect any current in the main circuit

after the execution time has elapsed. Otherwise, the fault

message"trip - execution STOP command" will be issued.

The contactor controls can only be connected after the fault

has been rectified.

Interlocking time (CiR)

SIMOCODE pro prevents, e.g. in the case of reversing

starters, both contactors from switching on at the same

time. Switching from one direction of rotation to the other

can be delayed via the interlocking time. Default: 0 s.

Summary of Contents for SIMOCODE 3UF













































































































































































Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands

Siemens SIMOCODE 3UF, Programming And Operating Manual

Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands