Siemens SIMOCODE 3UF Programming And Operating Manual Download Page 28

Page: 28 / 172

Motor Protection

7.2 Unbalance Protection

SIMOCODE PRO V PN FDI

Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

7.2

Unbalance Protection

The extent of the phase unbalance can be monitored and transmitted to the control system.

A definable and delayable response can be tripped when an adjustable level is exceeded. If

the phase unbalance is greater than 50 %, a reduction of the tripping time according to the

overload characteristic curve takes place automatically since the heat development in motors

increases with asymmetric conditions.

Level (CiR)

The limit of the unbalance to which SIMOCODE pro is to react when overshot is set here.

Level:

0 to 100 %

Preset:

40 %

Response

Here you can choose the response of SIMOCODE pro in case of phase unbalance:

Response

Unbalance

Disabled

Signaling

Warning

Tripping

Delay (CiR)

The unbalance limit must be exceeded for the period of the set delay time before

SIMOCODE pro executes the desired response. Otherwise, there is no reaction.

Delay:

0 up to 25.5 s

Preset:

0.5 s

Summary of Contents for SIMOCODE 3UF













































































































































































Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands

Siemens SIMOCODE 3UF, Programming And Operating Manual

Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands