Siemens SIMOCODE 3UF Programming And Operating Manual Download Page 107

Page: 107 / 172

Standard Functions

12.8 Watchdog (PLC/DCS monitoring)

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

107

Settings PLC/PCS monitoring

Bus Monitoring

•

Activated: If a bus fault occurs, the "Trip - Bus" fault

message is generated and must be acknowledged.

•

Deactivated: No fault message; however, the "Status

- Bus o.k." information can be evaluated at anytime.

PLC/PCS monitoring - Input

Control of the Watchdog function block using the

monitored signal (any sockets, e.g. control bits from

PROFINET, etc.

PLC/PCS monitoring

•

Activated: If an SPS fault occurs, the "Trip -

PLC/DCS" fault message is generated and must be

acknowledged.

•

Deactivated: No fault message; however, the "Status

- PLC/DCS in Run" information can be evaluated at

anytime.

Bus/PLC-Fault - Reset

You can select whether faults are to be acknowledged

automatically or manually.
Range: Manual/Automatic.

Summary of Contents for SIMOCODE 3UF













































































































































































Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands

Siemens SIMOCODE 3UF, Programming And Operating Manual

Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands