Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Manual Download Page 97

Page: 97 / 193

5 Display / WBM Configuration

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

5.2.16.3 Automatic Addressing

If you select this option, a new slave added to the AS-i line with AS-i address “0” is assigned
the next free address.

Disable this option once you have connected all required slaves.

Keypad/Display

AS-i Line 1 > Address help > enable/disable

WBM: “Automatic Addressing” Tab

Parameter

Function

Automatic

addressing

Enables/disables addressing support

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Manual

Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands