Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Manual Download Page 51

Page: 51 / 193

5 Display / WBM Configuration

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

Logging In

Make the following entries in the Start window:

Name:

“admin”

Password: “admin”

Confirm your entries by clicking the “Login” button.

The default for both name and password is “admin”. The name cannot be modified.

Notice

You should therefore change the password (Section 5.2.4). The module clear/reset
function or resetting to factory defaults also resets the password.

Note

If you do not log in, you will not be able to make changes.
If no input is made for more than 10 minutes (default), you will be logged out

automatically. You can change the time before logout in “System > Configuration >

Settings”.

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Manual

Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands