Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Manual Download Page 178

Page: 178 / 193

178

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

10 Dealing with Problems / Error Displays

This chapter...

This chapter contains information on the special modes of the IE/AS-i LINK and
explains how to deal with errors.

10.1

Replacing a Defective AS-i Slave/Automatic Address
Programming

Simple Replacement of AS-i Slaves

Using the automatic address programming function, you can replace failed AS-i
slaves extremely simply.

Notice

Remember that “automatic address programming” is only possible in the following
situations:

−

The function is enabled

−

The IE/AS-i Link is in the protected mode

−

Only one AS-i slave has failed.

The sections below explain how to replace failed AS-i slaves using the automatic
address programming function.

Detecting a Defective AS-i Slave

If the AUP LED is lit, this indicates the following:

Exactly one slave has failed.

Automatic address programming by the IE/AS-i LINK is possible.

You can identify the failed AS-i slave, for example in the display in “AS-i

−

Lifelist”.

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Manual

Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands