Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Manual Download Page 153

Page: 153 / 193

8 Using the Data Record Interface

153

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

8.2.2.2

Get_Permanent_Parameter

Meaning

This call reads out slave-specific parameters stored on the IE/AS-i LINK.

The job cannot be used for all slaves of the combined transaction type.

Structure of the RecordDataRead service − Index 4

Byte

Meaning

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Version_hi = 0x00

Version_lo = 0x00

0x0

Parameter

0x0

Reserved 0x00

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Manual

Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands