Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Manual Download Page 90

Page: 90 / 193

5 Display / WBM Configuration

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

WBM: “Diagnostics” Tab

This page displays all the relevant data of the selected slave.

Parameter

Function

Detected

If the slave is detected, a check mark is set here.

Display of the IO code of an AS-i slave

Display of the ID code of an AS-i slave

ID1

Display of the extended ID1 code of an AS-i slave

ID2

Display of the extended ID2 code of an AS-i slave

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Manual

Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands