Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Manual Download Page 80

Page: 80 / 193

5 Display / WBM Configuration

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

5.2.12

Navigation “PROFINET IO −> Status”

This page displays information on PROFINET IO.

5.2.12.1 Status

Keypad/Display

PROFINET > Info > Device name > Change PROFINET device name

IP address Controller
Controller name (PROFINET device name of controller)
Connection (AR status online/offline)
Controller (Controller status RUN/STOP)
Update time [ms]

PROFINET > Error

WBM: “Status” Tab

Parameter

Function

PNIO device name

Displays the PROFINET device name of the link

Controller IP address

Displays the IP address of the PROFINET IO controller

Controller name

Displays the PROFINET device name of the controller

Connection status

Display of the connection status (online / offline) between link and

PROFINET IO controller. See also Section 8.2.1.8.

Controller status

Display of the operating state of the controller (RUN / STOP)

Update time

Display of the set update time in milliseconds

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Manual

Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands