Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Manual Download Page 185

Page: 185 / 193

A AS-Interface Protocol Implementation Conformance Statement (PICS)

185

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

Table A-2 , (Fortsetzung)

No.

Comment / Function implemented by / see

Section

Function or Call on the Host Interface

(symbolic representation)

Support of Combined transaction type 5

integrated

How the AS-i cycle time depends on the number of connected slaves

The AS-i cycle time can be calculated using the following formula:

cycl

= (1 + number of activated AS-i slaves) x 154

Note

If two AS-i slaves with extended addressing mode occupy the same address (for

example, address 5A and address 5B), this slave pair is calculated as one AS-i

slave in the above formula. The reason for this is that slave pairs with the same

address are addressed only in every second cycle. The cycle time in the formula

above is therefore doubled for such slaves.

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Manual

Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands