Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Manual Download Page 33

Page: 33 / 193

2 Procedure

−

Configuration

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

2.2

Configuration Options

There are four basic configuration options that are described in later chapters.

Configuration of the AS-Interface

Keypad/display (see Chapter 4)
Local configuration, commissioning and diagnostics of the AS-Interface

Web Based Management (WBM) (see Chapter 5)
Configuration, commissioning and diagnostics of the AS-Interface over a LAN

attachment using a PG/PC with an Internet Browser
You can change the configuration of the IE/AS-i LINK, check settings and

access diagnostic data (error list and statistics) over one of the two LAN

interfaces and WBM. WBM provides more extensive functions compared with

the keypad and display.

Configuration of the entire system

STEP 7 / HW Config (see Chapter 6)
Basic total configuration of the system and programming and diagnostics using

STEP 7
If required, additional configuration of the AS-Interface in STEP 7 (default: no

particular AS-i presettings)

Variable configuration of the AS-INTERFACE

Data record interface (see Chapter 8)
Variable configuration of the AS-Interface by the user program if AS-i

configurations change
You can also read out error counters and diagnostic data.

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Manual

Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands