Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 3

Page: 3 / 158

Table of contents

Introduction...................................................................................................................................................7

Safety notices.............................................................................................................................................13

Network topologies and redundancy..........................................................................................................17
3.1

PRP........................................................................................................................................17

3.2

HSR........................................................................................................................................20

3.3

HSR-PRP coupling.................................................................................................................24

3.3.1

Coupling of two HSR rings via a PRP network......................................................................24

3.3.2

Coupling of two PRP networks via an HSR ring....................................................................26

Descriptions of the products.......................................................................................................................29
4.1

Overview of the product characteristics.................................................................................29

4.2

Unpacking and checking........................................................................................................31

4.3

Components of the product....................................................................................................32

4.4

SCALANCE X204RNA...........................................................................................................33

4.4.1

Product characteristics...........................................................................................................33

4.4.1.1

SCALANCE X204RNA (PRP) product characteristics...........................................................33

4.4.1.2

SCALANCE X204RNA (HSR) product characteristics...........................................................34

4.4.2

SCALANCE X204RNA TP interfaces.....................................................................................35

4.5

SCALANCE X204RNA EEC..................................................................................................37

4.5.1

Product characteristics...........................................................................................................37

4.5.1.1

SCALANCE X204RNA EEC (PRP) product characteristics...................................................37

4.5.1.2

SCALANCE X204RNA EEC (PRP/HSR) product characteristics..........................................38

4.5.1.3

SCALANCE X204RNA EEC (HSR) product characteristics..................................................39

4.5.2

SCALANCE X204RNA EEC TP interfaces............................................................................40

4.5.3

SCALANCE X204RNA EEC SFP interface............................................................................42

4.6

C-PLUG..................................................................................................................................44

4.7

SELECT/SET button..............................................................................................................46

4.8

LEDs......................................................................................................................................49

4.8.1

SCALANCE X-200RNA (PRP)...............................................................................................49

4.8.1.1

Fault LED...............................................................................................................................49

4.8.1.2

Power LED.............................................................................................................................49

4.8.1.3

Port LED.................................................................................................................................50

4.8.1.4

LED displays during startup...................................................................................................50

4.8.1.5

Mode LED (SCALANCE X204RNA EEC (PRP/HSR))...........................................................51

4.8.2

SCALANCE X-200RNA (HSR)...............................................................................................51

4.8.2.1

Fault LED...............................................................................................................................51

4.8.2.2

Power LED.............................................................................................................................51

4.8.2.3

Port LED.................................................................................................................................52

4.8.2.4

LED displays during startup...................................................................................................52

4.8.2.5

Mode LED (SCALANCE X204RNA EEC (PRP/HSR))...........................................................53

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands