Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 8

Page: 8 / 158

Product names of the devices in these operating instructions

The descriptions in these operating instructions always apply to the devices of the SCALANCE

X‑200RNA product line listed under "Validity of the Operating Instructions" in this document

unless the description relates to a specific device of the product line.

Product name

Covers the following devices:

SCALANCE X-200RNA

SCALANCE X204RNA (PRP)
SCALANCE X204RNA (HSR)
SCALANCE X204RNA EEC (PRP)
SCALANCE X204RNA EEC (HSR)
SCALANCE X204RNA EEC (PRP/HSR)

SCALANCE X-200RNA (PRP)

SCALANCE X204RNA (PRP)
SCALANCE X204RNA EEC (PRP)
SCALANCE X204RNA EEC (PRP/HSR) in "PRP" mode

SCALANCE X-200RNA (HSR)

SCALANCE X204RNA (HSR)
SCALANCE X204RNA EEC (HSR)
SCALANCE X204RNA EEC (PRP/HSR) in "HSR" mode

SCALANCE X204RNA

SCALANCE X204RNA (PRP)
SCALANCE X204RNA (HSR)

SCALANCE X204RNA EEC

SCALANCE X204RNA EEC (PRP)
SCALANCE X204RNA EEC (HSR)
SCALANCE X204RNA EEC (PRP/HSR)

Note
SCALANCE X204RNA EEC (PRP/HSR)
This device can be configured either as a PRP device or as an HSR device.
If you configure the device as a PRP device, it behaves in exactly the same way as the

SCALANCE X204RNA EEC (PRP).
If you configure the device as an HSR device, it behaves in exactly the same way as the

SCALANCE X204RNA EEC (HSR).

Further documentation

The "SIMATIC NET Industrial Ethernet Twisted Pair and Fiber Optic Networks" manual and

the "Industrial Ethernet Network Manual" contain additional information on other SIMATIC NET

products that you can operate along with the devices of the SCALANCE X‑200RNA product

line in an Industrial Ethernet network. You will find further documentation on the Siemens

Automation Customer Support pages.

Introduction

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Brands by name

Popular brands

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Brands by name

Popular brands