Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 63

Page: 63 / 158

Connecting up

6.1

Power supply

Connecting the power supply

The power supply is connected using a 3- or 4-pin plug-in terminal block. Usable cable cross-

section 0.25 to 2.5 mm

. Permitted tightening torque 0.57 - 0.79 Nm (5 - 7 in.lb.).

The power supply is non-floating. The signal cables of the Ethernet TP ports are floating.

Note
Removing or inserting the power supply with the power on is not permitted.

Coding
With the SCALANCE X204RNA EEC the supplied plugs and the socket on the device for the

power supply match in their coding.
The plug and socket for the signaling contact are coded differently from the connection of the

power supply. The plugs for power supply and signaling contact cannot therefore be

interchanged.
You can use non-coded plugs in coded sockets and coded plugs in non-coded sockets.

Pin assignment

Pin number

Pin assignment of the SCALANCE X204RNA

(PRP and HSR)

Pin assignment of the SCALANCE X204RNA EEC

(PRP and HSR and PRP/HSR)

Pin 1

L1 +24 VDC

PE
Coding of the socket

Pin 2

L1 +24 V … +250 VDC

L1 100 V … 240 VAC
Coding of the plug

Pin 3

N1
Coding of the socket

Pin 4

L2 +24 VDC

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands