manualshive.com logo in svg

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Share
Download
Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 124

● "Aging Enabled"

A SCALANCE X-200RNA automatically learns the source addresses of the nodes 

connected to it. This information is used in the SCALANCE X-200RNA to forward data 

frames to the nodes specifically involved. This reduces the network load for the other nodes.

If a SCALANCE X-200RNA does not receive a frame whose source address matches a 

learnt address within a certain time, it deletes the learnt address. This mechanism is known 

as aging. Aging prevents frames being forwarded incorrectly, for example when an end 

device (for example a programming device) is connected to a different switch port.

If the check box is not enabled, a SCALANCE X-200RNA does not delete learnt addresses 

automatically.

● "Aging Time [sec]"

Here, you enter the time after which the SCALANCE X-200RNA deletes an address if it 

has not received frames with the corresponding sender address.   

Here, the aging time can be set as required within the range from 1 to 655 seconds.

7.10.3

Port status

Overview of the configuration of the ports

The "Port Status" dialog box appears if you click the "Ports" folder icon.
The dialog box shows the configuration for data transfer for all ports of the SCALANCE 

X-200RNA.   

Figure 7-38 Port status

Functional description and configuration using Web Based Management
7.10 The "Switch" menu

SCALANCE X-200RNA

124

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands