Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 18

Page: 18 / 158

The SCALANCE X-200RNA can manage a maximum of 1023 MAC addresses.

Note
Keep to the maximum permitted cable lengths of the devices you are using. You will find the

permitted cable lengths in the technical specifications.

Example

Figure 3-1

Schematic diagram of the "Parallel Redundancy Protocol"

With the "Parallel Redundancy Protocol" (PRP), each node must transmit Ethernet frames on

two independent, parallel networks. These are two physically separate networks with a bus

(linear), star or ring topology. The PRP destination device must also be connected to the two

networks. This then receives each frame twice. The first frame is forwarded to the application.

Network topologies and redundancy
3.1 PRP

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands