Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 65 | Manualshive

Page: 65 / 158

background image

Power supply 100 AC .. 240 V / 24 .. 250 VDC

WARNING

Danger from line voltage
The SCALANCE X204RNA EEC has a power supply of 100 to 240 VAC or 24 to 250 VDC.
This product can only function correctly and safely if it is transported, stored, set up, and

installed correctly, and operated and maintained as recommended.
Connecting and disconnecting may only be performed by an electrical specialist. Connect or

disconnect power supply cables only when the power is turned off.

WARNING

The SCALANCE X204RNA EEC does not have an ATEX approval.
Devices with a 100 to 240 VAC or 24 to 250 VDC power supply are not approved for use in

hazardous areas according to EC‑RL‑-94/9 (ATEX).

NOTICE
Securing cables with dangerous voltage
Make sure that the connector cannot be released accidentally by pulling on the connecting

cable. Lay the cables in cable ducts or cable channels and secure the cables, where

necessary, with cable ties.

Protective ground

WARNING

PE connector of SCALANCE X204RNA EEC
Simple grounding via the housing is inadequate. For reliable operation, the PE cable must

be connected via the ground bolt. On the SCALANCE X204RNA EEC, the grounding bolt is

on the bottom of the device.

Connecting up

6.1 Power supply

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

65

«
...
63
64
65
66
67
...
»

Summary of Contents for SCALANCE X-200RNA































































































































































Reviews:

No comments

Related manuals for SCALANCE X-200RNA

Brand: FAAC Pages: 2

3C16710 - OfficeConnect 8/TPM Hub

Brand: 3Com Pages: 130

Brand: Homefibre Pages: 2

Brand: Cabletron Systems Pages: 83

Brand: Davey Pages: 2

Brand: Lantech Pages: 24

Brand: National Instruments Pages: 8

Brand: ALFAtron Pages: 23

Brand: Nxg Pages: 2

Brand: Thinklogical Pages: 45

Brand: ALFAtron Pages: 45

Brand: Yacoub Automation GmbH Pages: 45

Brand: N-Tron Pages: 152

Brand: Atlona Pages: 17

Brand: NETGEAR Pages: 2

Brand: Raritan Pages: 46

Tripp-Lite B005-HUA2-K

Brand: Eaton Pages: 4

xComfort CTAA-01/01

Brand: Eaton Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands