manualshive.com logo in svg

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Share
Download
Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 100

Settings in WBM

In WBM, you can set the monitoring of the power supply (SCALANCE X204RNA only) and the 

device-related link monitoring. The settings are made in three separate dialog boxes:

Figure 7-19 SCALANCE X204RNA Fault Mask Power Monitoring

Enable Power Monitoring (SCALANCE X204RNA only) 

Here, you specify which of the two power supplies of the SCALANCE X204RNA (line 1 and 

line 2) is monitored. A fault is then indicated by the message system when there is no power 

on one of the monitored lines (line 1 or line 2) or when the voltage is too low (less than 14 V).

Note
This dialog box is not displayed with the SCALANCE X204RNA EEC because it does not have 

a redundant power supply.

Functional description and configuration using Web Based Management
7.8 The "X200" menu

SCALANCE X-200RNA

100

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands