manualshive.com logo in svg

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Share
Download
Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 56

NOTICE
Do not cover the ventilation grilles
During installation, select a mounting position so that the ventilation grilles are always free to 

achieve adequate cooling. With normal orientation, the ventilation grilles are on the top, 

bottom and sides (SCALANCE X204RNA EEC only) of the housing.

Minimum clearances

If you install the SCALANCE X-200RNA without forced ventilation or cooling, minimum 

clearances must be maintained to neighboring devices or the wall of the housing. By keeping 

to the minimum clearances, there is then an adequate stream of air for heat dissipation during 

operation. Keep to the following minimum clearances to neighboring devices.

Table 5-1

Minimum clearances when installing in cabinets

Minimum clearance to devices below the SCALANCE X-200RNA

100 mm

Minimum clearance to devices above the SCALANCE X-200RNA

100 mm

Minimum lateral clearance to devices (SCALANCE X204RNA EEC only) 20 mm

Installation
5.1 Types of installation

SCALANCE X-200RNA

56

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands