Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 64 | Manualshive

Page: 64 / 158

background image

Note
Since the SCALANCE X204RNA EEC does not have a redundant power supply, connect the

power supply between L1 and N1.

WARNING

The SCALANCE X204RNA is designed for operation with safety extra-low voltage (SELV).

This means that only safety extra-low voltages (SELV) complying with IEC950/EN60950/

VDE0805 can be connected to the power supply terminals.
Measures must be taken to prevent transient overvoltages of more than 40% of the rated

voltage. This is the case if the devices are operated exclusively with SELV (Safety Extra Low

Voltage).
The power supply unit for the SCALANCE X204RNA power supply must meet NEC Class 2,

as described by the National Electrical Code(r) (ANSI/NFPA 70).
The power of all connected power supply units must total the equivalent of a power source

with limited power (LPS limited power source).
If the device is connected to a redundant power supply (two separate power supplies), both

must meet these requirements.
The signaling contact can be subjected to a maximum load of 100 mA (safety extra-low

voltage (SELV), 24 VDC).
Never operate the SCALANCE X204RNA (PRP and HSR) with AC voltage or DC voltage

higher than 28.8 V DC.

24 VDC power supply

NOTICE
If the SCALANCE X204RNA is supplied over long 24 V power supply lines or networks,

measures are necessary to prevent interference by strong electromagnetic pulses on the

supply lines. These can result, for example, due to lightning or switching of large inductive

loads.
One of the tests used to attest the immunity of the SCALANCE X204RNA to electromagnetic

interference is the "surge immunity test" according to EN61000-4-5. This test requires

overvoltage protection for the power supply lines. A suitable device is, for example, the Dehn

Blitzductor BVT AVD 24 V type no. 918 422 or a comparable protective element.
Manufacturer: DEHN+SÖHNE GmbH+Co.KG, Hans-Dehn-Str.1, Postfach 1640, D-92306

Neumarkt, Germany.

Connecting up
6.1 Power supply

SCALANCE X-200RNA

64

Operating Instructions, 10/2016, C79000-G8976-C342-04

«
...
62
63
64
65
66
...
»

Summary of Contents for SCALANCE X-200RNA































































































































































Reviews:

No comments

Related manuals for SCALANCE X-200RNA

DGS-1024D - Switch

Brand: D-Link Pages: 16

DGS-1016D - Switch

Brand: D-Link Pages: 44

DES-6000 Series

Brand: D-Link Pages: 3

DES-5024 - Switch

Brand: D-Link Pages: 2

DES-3828 - xStack Switch - Stackable

Brand: D-Link Pages: 3

Brand: D-Link Pages: 192

Brand: D-Link Pages: 9

Brand: D-Link Pages: 110

Brand: D-Link Pages: 10

Brand: D-Link Pages: 17

Brand: D-Link Pages: 4

Brand: D-Link Pages: 9

Brand: D-Link Pages: 4

DGS-105 - Switch

Brand: D-Link Pages: 4

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

Brand: GE Pages: 20

Brand: Hama Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands