manualshive.com logo in svg

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Share
Download
Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 26

3.3.2

Coupling of two PRP networks via an HSR ring

+65

353

353

6&$/$1&(

;51$

6&$/$1&(

;51$

6&$/$1&(

;51$

6&$/$1&(

;51$

6&$/$1&(

;51$

6&$/$1&(

;51$

6&$/$1&(

;51$

6,0$7,&6

&351$

3&

6,0$7,&6

3&

/$1$

/$1%

/$1$

/$1%

Figure 3-5

Topology of a coupling of two PRP networks via an HSR ring

Settings in WBM

You specify the functionality of the devices SCALANCE X204RNA 

①

 to 

④

 relating to the 

coupling of the two PRP networks on the WBM page X200 > Coupling Configuration. You need 

to configure the following parameters:
● Coupling Mode
● NetID

Configuration of the "Coupling Mode" parameter

Setting for device 

①

 and 

③

Redundant HSR PRP coupling, LAN A (The port P2/B is open and must not be used.)

Network topologies and redundancy
3.3 HSR-PRP coupling

SCALANCE X-200RNA

26

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands