Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 37

Page: 37 / 158

4.5

SCALANCE X204RNA EEC

4.5.1

Product characteristics

4.5.1.1

SCALANCE X204RNA EEC (PRP) product characteristics

Possible attachments

The SCALANCE X204RNA EEC (PRP) has four RJ-45 jacks and two slots for SFP modules.

The SFP modules can be used as an alternative to the two RJ-45 jacks PRP A and PRP B

and are intended for the connection of the LAN A and LAN B networks. End devices or network

segments without PRP capability are connected to the RJ-45 jacks P1 and P2.

Figure 4-4

SCALANCE X204RNA EEC (PRP)

Descriptions of the products

4.5 SCALANCE X204RNA EEC

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Brands by name

Popular brands

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Brands by name

Popular brands