manualshive.com logo in svg

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Share
Download
Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 40

4.5.2

SCALANCE X204RNA EEC TP interfaces

Connector pinout

On the SCALANCE X204RNA EEC (PRP and HSR), the TP interfaces are implemented as 

RJ-45 jacks with the MDI-X assignment (Medium Dependent Interface Autocrossover) of a 

network component.   

Figure 4-7

RJ-45 jack

Table 4-4

Pin assignment

Pin number

Assignment

Pin 8

n. c.

Pin 7

n. c.

Pin 6

TD-

Pin 5

n. c.

Pin 4

n. c.

Pin 3

TD+

Pin 2

RD-

Pin 1

RD+

Note
TP cords or TP-XP cords with a maximum length of 10 m can be connected to the RJ-45 TP 

port.
With the IE FC cables and IE FC RJ-45 plug 180, an overall cable length of up to 100 m is 

permitted between two devices depending on the cable type.

Note
The interfaces of the SCALANCE X204RNA EEC (PRP and HSR and PRP/HSR) meet the 

requirements for environment B according to IEEE 802.3, section 33.4.1.1.

Descriptions of the products
4.5 SCALANCE X204RNA EEC

SCALANCE X-200RNA

40

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands