Siemens SCALANCE X-200RNA Operating Instructions Manual Download Page 35

Page: 35 / 158

4.4.2

SCALANCE X204RNA TP interfaces

Connector pinout

On the SCALANCE X204RNA, the TP interfaces are implemented as RJ-45 jacks with the

MDI-X assignment (Medium Dependent Interface Autocrossover) of a network component.

Figure 4-3

RJ-45 jack

Table 4-3

Pin assignment

Pin number

Assignment

Pin 8

n. c.

Pin 7

n. c.

Pin 6

TD-

Pin 5

n. c.

Pin 4

n. c.

Pin 3

TD+

Pin 2

RD-

Pin 1

RD+

Note
TP cords or TP-XP cords with a maximum length of 10 m can be connected to the RJ-45 TP

port.
With the IE FC cables and IE FC RJ-45 plug 180, an overall cable length of up to 100 m is

permitted between two devices depending on the cable type.

Note
The interfaces of the SCALANCE X204RNA meet the requirements for environment B

according to IEEE 802.3, section 33.4.1.1.

Descriptions of the products

4.4 SCALANCE X204RNA

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

Summary of Contents for SCALANCE X-200RNA































































































































































Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands

Siemens SCALANCE X-200RNA, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X-200RNA

Reviews:

Related manuals for SCALANCE X-200RNA

Brands by name

Popular brands