Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional Operating Manual Download Page 27 | Manualshive

Page: 27 / 154

background image

Putting the handset into service

17

Inserting/replacing the memory card and the

battery pack

The handset comes with an approved battery pack and memory card.

Battery pack

The battery pack is not charged. It is first charged in the handset.

The Ex battery pack features special electronics. Gigaset M2 Ex profes-
sional detects whether an Ex battery pack or a normal battery pack is in-
serted. The handset will not switch on if a normal battery pack is inserted.

Memory card

The memory card is located under the battery pack. Phonebook and calen-
dar functions cannot be performed without the memory card.

The memory card contains the following data:
•

Phonebook entries/redial list

•

Calendar entries/appointments

You can transfer your memory card to a new Gigaset M2 handset if your
original handset is defective. This ensures you do not lose your data.

Notes:

•

Note: Please observe the safety notes on the back cover.

•

Ageing can diminish the battery pack capacity making it insuffi-
cient for the anticipated length of operation (discharging
speeds up over time). The battery pack must be replaced by
specially qualified technicians if this happens.

•

Only use the approved battery pack (

Æ

Page 21).

•

Open the battery compartment outside the Ex zone and in a
dust-free environment only.

•

Your telephone directory entries and all settings remain stored
even if you remove the battery pack. The date and time settings
will be reset.

«
...
25
26
27
28
29
...
»

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional



























































































































































Reviews:

No comments

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brand: TCL Pages: 27

Brand: NEC Pages: 7

Brand: NEC Pages: 68

Brand: NEC Pages: 44

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 312

Brand: Panasonic Pages: 311

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 17

Brand: Panasonic Pages: 2

Brand: Palm Pages: 28

700wx - Treo Smartphone 60 MB

Brand: Palm Pages: 2

700wx - Treo Smartphone 60 MB

Brand: Palm Pages: 30

700w - Treo Smartphone 60 MB

Brand: Palm Pages: 14

Brand: Diamond Tech Pages: 38

Brand: E-TEN Pages: 30

Brand: i-mobile Pages: 99

Brand: Docomo Pages: 596

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands