Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional Page 142 Operating Manual Download

Page: 142 / 154

Appendix

132

Accessories

Only use original accessories. This will help you avoid injury and property
damage and you can ensure that all relevant regulations are observed.

Data cable

Source

For information on accessories (such as, headsets, data cables, MPM soft-
ware), contact Siemens at the following address:

Siemens AG, I&S IS SC S RC, Tübingerstrasse 1-5, 80686 Munich
Mr. Jens Schwabe
Tel.: +49 89 9221 - 3174
Fax: +49 89 9221 - 6603
E-mail: [email protected]

Directives and standards

The handset and accessories listed conform to the following EU directives
and standards:

EU guidelines

Headset:

Headsets from different manufactur-
ers may be used.

Data cable DCA-500:

To connect the handset to the serial
RS232 interface on your computer
(not suitable for Gigaset M2 Ex pro-
fessional)

Data cable USB DCA-510:

To connect the handset to the USB
interface on your computer

•

89/336/EC "Electromagnetic Compatibility"

•

73/23/EC "Electrical apparatus for use within specific
voltage parameters"

•

94/9/EC "Equipment intended for use in potentially ex-
plosive atmospheres" (not suitable for Gigaset M2 Ex
professional)

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional



























































































































































Search results

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional

Reviews:

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brands by name

Popular brands

Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional, Operating Manual

Search results

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional

Reviews:

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brands by name

Popular brands