Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional Operating Manual Download Page 110

Page: 110 / 154

Step by Step

Message functions

100

Answering a message or voice-mail
message

An advisory message appears and the message key
flashes when one or more information messages or
voice mails have been received for you.

Viewing a new message

either:

Press the message key.

or:

Press and hold down the Talk key or press the Speaker-
phone key.

Call the system menu.

> <

[

Select the menu item and confirm.

> [

Select the required message and confirm your selec-
tion.

then:

Call the additional menu.

> <

[

Select the menu item and confirm.

Call the additional menu.

> <

[

Select the menu item and confirm. The time of the
message is displayed.

either:

Call the additional menu.

> <

[

Select the menu item and confirm. You call back the
sender.

or:

> <

[

Select the menu item and confirm. The entry is deleted.

then:

Press the On-hook key to end the operation.

Menu

Display Messages?

Msg. from:
...

Mnu

Text?

Mnu

Time/date sent?

Mnu

Call Sender?

Delete?

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional



























































































































































Search results

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional

Reviews:

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brands by name

Popular brands

Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional, Operating Manual

Search results

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional

Reviews:

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brands by name

Popular brands