Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional Operating Manual Download Page 127

Page: 127 / 154

Additional functions

117

Step by Step

On the other handset:

[

Enter the Bluetooth PIN immediately and confirm (de-
fault: 0000). If you were not fast enough, repeat the pre-
vious steps.

[

Confirm the prompt.

The Bluetooth connection is established. The two hand-
sets can now exchange data in vCard format.

Transferring data

Open the phonebook.

Select the entry.

Open the handset’s phonebook menu.

either:

[

Select the menu item and confirm.

or:

[

Select the menu item and confirm.

then:

[

Select the menu item and confirm.

[

Select and confirm the target device or handset. The
vCard data is sent to the target device.

Now follow the instructions on your handset display.

agreed PIN:

Add to
Trusted Device
list?

Copy List

Copy Entry

vCard via Bluetooth:

Trusted Devices
...

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional



























































































































































Search results

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional

Reviews:

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brands by name

Popular brands

Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional, Operating Manual

Search results

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional

Reviews:

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brands by name

Popular brands