Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional Page 125 Operating Manual Download | Manualshive

Page: 125 / 154

background image

Additional functions

115

PC interface (V24, USB)

You can use the PC interface (via a Slim Lumberg cable) to read and modify
phonebook entries, pictures and sounds.

Configuring the PC interface

To configure the PC interface, you must:

1. deactivate the Bluetooth interface on the handset (

Æ

Page 118).

2. use a Siemens data cable (

Æ

Page 132) to connect the headset/PC in-

terface jack on the handset to the computer.

3. install the MPM application.

For more information, consult your system administrator.

Data transfer mode

Certain functions necessitate the transfer of large volumes of data be-
tween the handset and the computer. When these functions are selected,
the handset switches to data transfer mode and "Data Transfer" appears on
the display. In this mode, no inputs are possible via the keyboard and calls
are ignored.

The handset is switched to data transfer mode by:
•

activating read/write access to the phonebook

•

loading screensavers

•

loading melodies

Note:

If the PC interface does not work, first deactivate the Bluetooth in-
terface (

Æ

Page 118), then switch the handset off and back on.

Note:

The handset automatically switches to idle if a fault occurs in the
course of transferring data.

«
...
123
124
125
126
127
...
»

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional



























































































































































Reviews:

No comments

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brand: Icemobile Pages: 59

Brand: T-Mobile Pages: 4

Brand: Samsung Pages: 252

Galaxy S20 FE 5G

Brand: Samsung Pages: 19

Galaxy S Epic SPH-D700

Brand: Samsung Pages: 264

Galaxy S II Skyrocket SGH-i727

Brand: Samsung Pages: 206

Galaxy S Plus GT-I9001

Brand: Samsung Pages: 147

Brand: Samsung Pages: 48

Galaxy J7 Prime

Brand: Samsung Pages: 33

Brand: Samsung Pages: 32

Brand: Samsung Pages: 2

Brand: Samsung Pages: 11

Brand: Samsung Pages: 2

Brand: Samsung Pages: 65

Brand: Samsung Pages: 2

Galaxy Amp Prime 3

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 163

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands