Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional Page 81 Operating Manual Download

Page: 81 / 154

Conducting calls – enhanced functions

Step by Step

Activating control relays

The service engineer can set up a maximum of 4 control
relays that enable various equipment (forexample, door
opener) to be activated and deactivated.

It is possible to access a specific control relay. Depend-
ing on the configuration, the control relays can be
•

activated and deactivated automatically, or

•

activated and deactivated automatically on the basis
of a timer.

Prerequisite: The service engineer has set up at least
one switch.

This function can also be called by entering the code
(

Page 123).

Activating a control relay

Press and hold down the Talk key or press the Speaker-
phone key.

Call the system menu.

> <

[

Select the menu item and confirm.

> <

[

Select the menu item and confirm.

Follow the user guidance system from this point on-
wards. Enter the required switch code (1... 4).

Press the On-hook key to end the operation.

Deactivating a control relay

Press and hold down the Talk key or press the Speaker-
phone key.

Call the system menu.

> <

[

Select the menu item and confirm.

> <

[

Select the menu item and confirm.

Follow the user guidance system from this point on-
wards. Enter the required switch code (1... 4).

Press the On-hook key to end the operation.

Menu

Service?

*90=Control Relay

On?

Menu

Service?

#90=Control Relay
Off?

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional



























































































































































Search results

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional

Reviews:

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brands by name

Popular brands

Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional, Operating Manual

Search results

Summary of Contents for HiPath 3000 V3.0 or later Gigaset M1 Professional

Reviews:

Related manuals for HiPath 3000 V3.0 or later Gigaset M1 Professional

Brands by name

Popular brands